[April 2018] 2018 New Lead2pass Juniper JN0-647 Dumps Free Download 80q

2018 New Released Juniper JN0-647 Exam Dumps Free Download In Lead2pass:

https://www.lead2pass.com/jn0-647.html

QUESTION 41
Which policy statement will be applied to neighbor 172.16.4.2?

A.    policy-statement all and policy -statement agg
B.    policy-statement agg
C.    policy-statement all and policy -statement atat
D.    policy-statement atat

Answer: A

QUESTION 42
You are attempting to configure BGP peering to a new service provider. The BGP peering state is stuck in the active state.
What are two reasons for this happening? (Choose two)

A.    the local autonomous system number is not configure
B.    the origin ID is not configure
C.    The peer IP address is incorrect
D.    The peer autonomous number is incorrect.

Answer: C

QUESTION 43
You manage your company enterprises network using EX series switches. Your company wants to use Q in Q tunneling to connect remote customer sites together. Which statement is correct about the scenario?

A.    You must enable L2PTto tunnel layer 2 protocol traffic
B.    The outside layer 2 frame is popped by the penultimate switch
C.    Customer traffic is tunneled through the network using the C VLAN ID
D.    The default Ethernet value is 0x9100

Answer: A

QUESTION 44
Which two statements about VSTP on EX series switches are connect? (Choose two)

A.    All VLANS beyond the first 64 will not be supported by VSTP
B.    VSTP automatically assigns each VLAN to one spanning tree instances
C.    VSTP must be used to intemperate with MVRP
D.    VSTP must be used to intemperate with PVST+

Answer: BD

QUESTION 45
Referring to the exhibit, R2 is exporting the route for server1 as a Type 2 external route and R6 is exporting the route for server 1 as a type 1 external route in OSPF.
Which path is taken to reach server-1 from user1?

A.    R1>R3>R6
B.    R1>R2
C.    R1>R4>R6
D.    R1>R2>R4>R6

Answer: D

QUESTION 46
Which statement is correct regarding the isolated ports?

A.    isolated ports are trunk ports that have layer 2 connectivity with all other ports
B.    isolated port are access ports that only have layer 2 connectivity with other isolated port
C.    isolated port are access port that only have layer 2 connectivity with promosious ports
D.    isolated port are trunk ports that have layer 2 connectivity with all community ports

Answer: C

QUESTION 47
Your network provider supports multicast traffic but your provider network does not. You want to allow multicast hosts outside of your network to receive multicast traffic sourced within your network.

How would you satisfy this requirement?

A.    Use MSDP peering with your provider.
B.    Use AutoVPN to connect to the remote hosts.
C.    Use an MP-BGP session to your provider to pass multicast traffic.
D.    Use automatic multicast tunnel gateway at the edge of your network.

Answer: D

QUESTION 48
Click the exhibit.

481

Referring to the exhibit, traffic handled by the s-1 scheduler is out of profile. Assuming bandwidth is available in this scenario, which statement is correct?

A.    Traffic handled by the s-1 scheduler is serviced immediately after traffic being serviced by the s-4 scheduler.
B.    Traffic handled by the s-1 scheduler is serviced immediately before traffic being serviced by the s-4 scheduler.
C.    Traffic handled by the s-1 scheduler is serviced immediately before traffic being serviced by the s-2 scheduler.
D.    Traffic handled by the s-1 scheduler is serviced immediately after traffic being serviced by the s-2 scheduler.

Answer: D

JN0-647 dumps full version (PDF&VCE): https://www.lead2pass.com/jn0-647.html

Large amount of free JN0-647 exam questions on Google Drive: https://drive.google.com/open?id=1KdYnfjldTm71Qle4hxd8vwiskvK9pf_L

You may also need:

JN0-643 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDQzh5Nk1hOG0tLUE

[March 2018] Lead2pass Free JN0-647 Exam Dumps With PDF And VCE Download 80q

Free Download JN0-647 Exam Dumps VCE From Lead2pass:

https://www.lead2pass.com/jn0-647.html

QUESTION 31
Click the Exhibit.

311

312

You have deployed the access control configuration to the distribution switch.

Referring to the exhibit, which statement is true?

A.    All hosts connected to the access switch require authentication to access the network.
B.    All hosts connected to the access switch will have access to the network after one host authenticates.
C.    All hosts connected to the access switch will have access to the network without authentication.
D.    Only the first host to authenticate will have access to the network, other hosts will be blocked.

Answer: B

QUESTION 32
Click the Exhibit.

321

Referring to the exhibit, traffic from User-1 is being forwarded to Server-1 with DSCP values that must be written. You must maintain the rewritten DSCP values throughout the network.

Which statement is correct in this scenario?

A.    At a minimum, you must rewrite the DSCP values on R1.
B.    At a minimum, you must rewrite the DSCP values on R1 and R4.
C.    At a minimum, you must rewrite the DSCP values on R1, R2, and R3.
D.    At a minimum, you must rewrite the DSCP values on R4.

Answer: D

QUESTION 33
Click the Exhibit.

331

You are adding a Junos Fusion satellite device but one cascade port is not coming on line.

Referring to the exhibit, what would cause this problem?

A.    The satellite device is not an EX4300.
B.    The cascade ports need to be on the same line card.
C.    The FPC number must match the FPC connecting to the satellite device.
D.    Interface xe-8/2/1 is in a link down state.

Answer: D

QUESTION 34
In Layer 2 environment where 802.1X is deployed with its default parameters on EX Series, which two statements are correct? (Choose two.)

A.    RADIUS authentication requests are sent from authenticator to the authentication server.
B.    DHCP traffic from supplicants is denied by default through the authenticator.
C.    RADIUS authentication requests are sent from the supplicant to the authentication server.
D.    DHCP traffic from supplicants is permitted by default through the authenticator.

Answer: AB

QUESTION 35
Click the Exhibit.

351

Your network is experiencing congestion across the link between R2 and R3. You must make changes to alleviate traffic congestion from R3 to R2.

Referring to the exhibit, which two commands would accomplish this task? (Choose two.)

A.    [edit protocol ospf]
user@R1# set reference-bandwidth 10g
B.    [edit protocol ospf]
user@R3# set reference-bandwidth 10g
C.    [edit protocols ospf area 0.0.0.0 ]
user@R1# set interface fe-1/0/1 metric 5
D.    [edit protocols ospf area 0.0.0.0 ]
user@R3# set interface fe-1/0/1 metric 5

Answer: BD

QUESTION 36
Which two statements are correct about using LLDP on junos devices? (Choose two)

A.    LLDP operates on layer 2 and layer 3 interfaces
B.    LLDP can interoperate with the cisco discovery protocol CDP
C.    LLDP is enabled on all devices by default
D.    LLDP operates on layer 2 interfaces

Answer: AC

QUESTION 37
You have certainly implemented the configuration shown in the exhibit. After committing these changes, the community devices connected to AS-1 are not able to communicate with the appropriate community devices connected to AS-2.
What must be done to allow these community devices to communicate?

A.    You must configure an isolation VLAN ID Under the pvlan-200 on the AS2
B.    switch You must configure the ge-0/0/10 interface on AS1 AS THE VPLAN on both switches
C.    You must configure an isolation VLAN ID under the VLAN 200 ON both switches
D.    You must configure the ge-0/012 interface on both switches as P VLAN trunks

Answer: D

QUESTION 38
Which two statements is true regarding the next hop attribute? (Choose two)

A.    it is not changed when sent across EBGP sessions
B.    it is changed to self for IBGP routes learned from EBGP
C.    it is not changed for IGBP routes learned from EBGP
D.    it is Changed by default when sent across EBGP sessions

Answer: CD

QUESTION 39
Your enterprise network is providing layer 2 connectivity between remote-sites using Q-in- Q tunneling. A customer wants to ensure their connection through your network is also participating in their spanning free topology. In this scenario, which solution must be used?

A.    you must configure the Q in Q tunnel to use L2PT to tunnel STP packets
B.    you must configure the same isolation ID on both sides of the tunnel
C.    you must configure spanning tree on the interfaces connected to the customers sites
D.    you must configure spanning tree to tunnel packets

Answer: A

QUESTION 40
You want to deploy MSTP with multiple regions. Each region should have a unique root bridge to accommodate a set of VLANs. Which three configuration elements must watch on switches participating in this deployment scenario? (Choose three)

A.    MSTI toVLAN mapping
B.    revision level
C.    CST BPDU parameters
D.    configuration name
E.    bridge priority

Answer: ABD

JN0-647 dumps full version (PDF&VCE): https://www.lead2pass.com/jn0-647.html

Large amount of free JN0-647 exam questions on Google Drive: https://drive.google.com/open?id=1KdYnfjldTm71Qle4hxd8vwiskvK9pf_L

You may also need:

JN0-643 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDQzh5Nk1hOG0tLUE

[January 2018] JN0-647 Exam Dump Free Updation Availabe In Lead2pass 80q

Juniper JN0-647 Latest Dumps Free Download From Lead2pass:

https://www.lead2pass.com/jn0-647.html

QUESTION 21
You are asked to merge a RIP network with your OSPF network. As a first step, you establish connectivity between the RIP network and the OSPF network. The RIP network connects to an NSSA area. Which two statements are true in this scenario? (Choose two.)

A.    To share RIP routes with the OSPF network, an export policy will be required on the ABR.
B.    To share RIP routes with the OSPF network, an export policy will be required on the ASBR.
C.    By default, external OSPF routes have a higher route preference than RIP routes.
D.    Be default, RIP routes have a higher route preference than external OSPF routes. Continue reading “[January 2018] JN0-647 Exam Dump Free Updation Availabe In Lead2pass 80q”

[Q1-Q10] Lead2pass 2017 New JN0-647 Exam PDF Ensure JN0-647 Certification Exam Pass Successfully

2017 New Lead2pass Juniper JN0-647 Dumps Free Download:

https://www.lead2pass.com/jn0-647.html

QUESTION 1
Your campus EX9200 core devices are highly oversubscribed on bandwidth ans reporting massive dropped packets. To immediately address the issue, you decide to implement shaping on all interfaces.

Which action will accomplish?

A.    Apply the input-shape-rate 5G parameter to all interfaces under the [edit class-of service] hierarchy.
B.    Define a CoS input traffic control profile with the shape-rate 5G parameter and apply it to all interfaces.
C.    Define a CoS output traffic control profile with the shape-rate 5G parameter and apply it to all interfaces.
D.    Apply the shape-rate 5G parameter to all interfaces under the [edit class-of service] hierarchy.] Continue reading “[Q1-Q10] Lead2pass 2017 New JN0-647 Exam PDF Ensure JN0-647 Certification Exam Pass Successfully”

[Juniper New] JN0-647 Latest Dumps Free Download From Lead2pass

Lead2pass 2017 November New Juniper JN0-647 Exam Dumps!

100% Free Download! 100% Pass Guaranteed!

Are you interested in successfully completing the Juniper JN0-647 Certification Then start to earning Salary? Lead2pass has leading edge developed Juniper exam questions that will ensure you pass this JN0-647 exam! Lead2pass delivers you the most accurate, current and latest updated JN0-647 Certification exam questions and available with a 100% money back guarantee promise!

Following questions and answers are all new published by Juniper Official Exam Center: https://www.lead2pass.com/jn0-647.html

QUESTION 1
Your campus EX9200 core devices are highly oversubscribed on bandwidth ans reporting massive dropped packets. To immediately address the issue, you decide to implement shaping on all interfaces.

Which action will accomplish?

A.    Apply the input-shape-rate 5G parameter to all interfaces under the [edit class-of service] hierarchy.
B.    Define a CoS input traffic control profile with the shape-rate 5G parameter and apply it to all interfaces.
C.    Define a CoS output traffic control profile with the shape-rate 5G parameter and apply it to all interfaces.
D.    Apply the shape-rate 5G parameter to all interfaces under the [edit class-of service] hierarchy.]

Continue reading “[Juniper New] JN0-647 Latest Dumps Free Download From Lead2pass”